The laboratory should be kept clean and free from clutter, by regular maintenance. At the completion of each experiment, equipment should be cleaned and properly stored. Do not let unused equipment or chemicals accumulate in the lab. Do not use the aisles of the lab or the space in front of the emergency escape panels for storage. Dispose of all hazardous wastes in accord with the procedures indicated in this manual. Reagent bottles must be properly labeled — when pouring hold the bottle with its label to your palm to protect the label. Notify your safety officer of bottles whose contents are in doubt.
Various types of eye protection listed in order of increasing effectiveness include:
Chemistry Department policy requires that all persons wear, at least, safety glasses (equipped with side shields), or goggles for eye protection while in the laboratory. In situations in which there is potential of a corrosive chemical being splashed into the eyes, safety glasses or goggles AND a face shield are required. In situations where there is potential for an explosion to occur, head shields are required in addition to safety glasses or goggles. Department policy on contact lenses in the laboratory is that you may wear contact lenses, but only if your eyes are protected as described in the preceding paragraph by safety glasses or goggles, with or without a face or head shield. Normal eye protection is required when you are wearing contact lenses since contact lenses provide little to no protection from chemicals in the eye. (In fact, contact lenses can complicate flooding the eye with water should a chemical get in the eye.) Safety goggles, with side shields are provided for chemistry employees (including all research students and teaching assistants) at no charge. Please see an Undergraduate Lab Manager or the Preparator. Prescription safety glasses are available (at your expense) through a local optometrist. Students who wear prescription glasses, and who do not wish to wear safety goggles (available at Bryan Center Store), must cover the costs involved in being fitted with prescription safety glasses. All undergraduates are expected to purchase and wear safety glasses at all times when they are working at their laboratory benches or in any area where hazardous activities could endanger their eyes. Teaching Assistants and faculty supervising them are expected to enforce this regulation at all times. Teaching Assistants are reminded that the safety performance of classes under their regulation is one of the criteria by which they will be evaluated by the faculty.
All persons in labs must wear shoes (bare feet or sandals are not allowed) and adequate clothing to protect the skin from spilled chemicals.
Always wear clothing that minimizes the amount of skin that can be exposed to potentially harmful chemicals. Never wear shorts in the lab. A lab coat or apron should be worn when working with hazardous materials. From DUKE OESO News, December 1997, Vol. 5, Number 4, pp 4-5. Of the ways chemicals can affect the human body, exposure through skin contact is one of the most significant. The skin does a wonderful job acting as a barrier to those conditions normally encountered in the environment; however, as our workplace environments use more and more chemical substances, our skin can no longer provide adequate protection on its own. Chemical substances can act on unprotected skin in three ways:
A chemical may cause damage by more than one of the above effects. Some examples include chlorinated solvents, such as ethylene dichloride, which will defat the skin causing irritation and tissue breakdown, also can permeate the skin possibly causing liver and kidney damage.
From DUKE OESO News, December 1997, Vol. 5, Number 4, pp 4-5. Our hands are the body parts most likely to be exposed to chemical contact under normal situations. Even though careful technique may help an employee avoid direct contact with a chemical; the potential for exposure still demands the use of protective gloves. The department of Chemistry maintains a small list of glove compatibilities . These charts are by no means complete. If you have any questions regarding the effectiveness of a glove with a specific chemical, contact OESO or visit the following glove manufacturer links:
"Karen E. Wetterhahn, professor of chemistry.... in the the Sciences at Dartmouth College, died June 8 at age 48 from mercury poisoning....While preparing the mercury NMR standard in a fume hood, Wetterhahn spilled one to a few drops of dimethylmercury. The compound permeated the latex gloves she was wearing and was absorbed through her skin into the bloodstream." C & EN, June 16, 1997, page 12.
In choosing a glove that will provide an adequate level of protection, it is important to keep three warnings in mind:
All chemicals will permeate through all glove materials. This process involves absorption of the chemical at the outside surface, diffusion of the chemical through the glove, and then desorption of the chemical from the inside of the glove. Gloves are considered protective if the rate of this permeation process is slow enough that the chemical does not break through to the inside. Glove manufacturers use two measures of glove suitability:
The objective in choosing a glove should be to seek a low permeation rate and a high breakthrough time, keeping in mind some of these factors:
There are many other factors that must be considered when selecting the glove that best suits the task. In some cases, your task may require you to choose a glove material which has a higher permeation rate, but has other qualities which makes it better for your situation. Some of these factors include:
General Guidelines For Glove Use, Care, and Hygiene:
The intent of this article was to present an overview of the complex nature of selecting the correct glove for adequate protection. Users should consult chemical MSDS's, glove manufacturer's literature, and the OESO for assistance.
Fume hoods provide constant respiratory protection in all laboratories in the building. Such protection is adequate for most controlled experiments. In using the hoods in the building, the following facts should be kept in mind. Additional information may be found in the OESO Laboratory Safety Manual or via the link on the OESO Laboratory Environment website labeled "OSHA Chemical Fume Hood Quick Facts".
The chemical fume hoods in the Department have been fitted with digital meters that provide the face velocity of airflow in feet per minute or FLO. FLO indicates the hood sash is fully closed so there is no face velocity. Makeup air is still being exhausted from the hood, but its velocity is not indicated on the guage. These gauges allow employees to check that the hood is functioning properly (i.e., have a minimum face velocity of 75 ft/min) every time they use the chemical hood. If a hood is not functioning properly, it should not be used and employees should call maintenance. Also place a sign on the hood so that others will not use it.
There are two types of emergency equipment available for respiratory protection: air-purifying and self-contained. These should only be used by Safety Office Personnel or others who have been instructed in their use. If you have need of respiratory protection equipment, contact the OESO.
In each lab there should be the following safety equipment: If you use any of the expendable safety items (such as a fire extinguisher), notify the OESO at 684-2794 as soon as possible so that replacements can be obtained.
Adjacent to the ice machine on the first level (hallway near 1112) there are spill kits for handling common spills involving 1) Solvents, 2) Acids (not for use with HF spills) and 3) Caustics. Directions for the use of each kit are provided with each kit. If you use one of these kits, notify the Lab Preparator (x1517, Room 1214) so that the used kit will be replaced. The used materials from the kit are to be kept in your lab (in a hood) and are to be treated as a hazardous waste. It is necessary to fill out a form requesting that this waste be removed from your lab by the OESO. (See the section dealing with disposal of waste chemicals later in this manual.)
Last updated on 7/25/2013